Microsoft Xbox 360 Controller Driver was listed since September 7, 2018 and is a great program part of Input Devices subcategory. It has achieved over 2,767 installations all time and 229 last week. It is available for Windows and the interface is in English. The program was created by Microsoft and has been updated on September 7, 2018. Step 2: Connect the Xbox 360 wired controller to your computer. Plug the Xbox 360 wired controller into any USB 2.0 or 3.0 port on the computer. Step 3: Test the controller. Open the Game Controllers dialog box. For Windows 8: At the Start screen on your computer, type joy.cpl. Then, in the search results, select joy.cpl. Select Xbox 360 Controller, and then select Properties.
Device downloads. For software and drivers, select your product from the list below. When I plug it into the USB port (Intel(R) ICH10 Family USB Enhanced Host Controller - 3A3C), it registers and installs the Xbox 360 Wireless Controller via Play & Charge Kit software. The controller is shown in Control Panel/Device Manager/Microsoft Common Controller for Windows Class Downloaded Microsoft Xbox 360 Accessories 1.1 (Xbox360_64Eng.exe) and installed.
Wireless Receiver
To use wireless Xbox 360 controllers, you will also need a USB wireless receiver plugged into your Raspberry Pi. The Official Microsoft Xbox 360 receiver or a generic brand like zettaguard, VicTsing will work. You can pair multiple controllers to a single wireless receiver. Play and charging cables will not work.
To pair your controller(s) with the wireless receiver:
- turn on your wireless Xbox 360 controller (hold down the Guide button)
- press the connect button on the receiver (green light will start flash)
- then press the tiny connect button on the top of the controller
- you will need to repeat these steps to pair each additional controller
Automatic Configuration (Easiest)
Xpad Driver
Starting with the RetroPie 4.1 SD image, the Xpad driver is enabled by default and the following steps are unnecessary.
With the recent kernel issues of xboxdrv rendering images unusable, there is an updated xpad driver which will work just as well for Xbox controllers, it's possible it may also support Xbox One controllers.
You access the driver through Manage Packages >> Manage Driver Packages >> Xpad Driver and you'll install it from source. Reboot for good measure, reconfigure your controllers and the lights should work properly.
A complete working config (that was generated from the EmulationStation configuration) is listed below at
/opt/retropie/configs/all/retroarch-joypads/Xbox360WirelessReceiver(XBOX).cfg
Xboxdrv Driver
Note! There are known incompatibilities with this driver when used in it's default configuration with the latest kernel. As such, the xpad drive is currently the best option to simply make an Xbox 360 controller operational in RetroPie.
However, these incompatibilities are not an issue when using xboxdrv as a calibration and key-mapping tool for almost any gamepad, including the Xbox 360 controller. When used this way, it's even possible for both xpad and xboxdrv to coexist together.
Access the RetroPie Setup Script and navigate to Manage Packages >> Manage Driver Packages >> xboxdrv
- Enable xboxdrv: This will install the driver and add a start-up configuration in /etc/rc.local
- Disable xboxdrv: This will disable the driver and remove the start-up configuration in /etc/rc.local
- Set Number of Controllers To Enable: Default number of controllers is 2 (If you have more than two controllers, set this first before you enable xboxdrv)
- Set Analog Stick Deadzone: Smaller number = more responsive, Larger number = less responsive.
- Set dwc_otg.speed=1 in /boot/config.txt: May help if controller is being glitchy.
- Remove dwc_otg.speed=1 from /boot/config.txt: Removes the config.
After you have enabled the driver and rebooted you'll need to reconfigure your controller(s) in EmulationStation as described on the first installation page
Alternatively if you prefer you can manually install it.
Manual Configuration
RetroPie 3.3 contains a newer xboxdrv at /opt/retropie/supplementary/xboxdrv/bin/xboxdrv - which is preferable over the older Debian package. On older RetroPie images you can install the Debian package.
install it by running
Then you must choose one of the 3 methods below
1 - Multiples instances of xboxdrv
You have to launch multiple instances of xboxdrv (one for each controller)
For example we can edit the file /etc/rc.local to start instances of xboxdrv during boot T_rex_na_kanojo download torrent.
Here is an example of what to insert in /etc/rc.local for 4 wireless pads (put this just before exit 0):
(replace the
--wid
by --id
if you use wired controllers)You must swich-on your pads before booting the raspberry.Husqvarna serial number decoding. Notice the
sleep 1
between each instance: this prevents the RPi from setting random controllers with random led status; adjust timing if necessary.2 - Single command line
Another way is to specify this single command :
3 - init script
The third possibility, you can use an init.d script with the daemon -D Option. Save the following content to /etc/init.d/xboxdrv:
sudo chmod +x /etc/init.d/xboxdrv
sudo update-rc.d xboxdrv start 90 2 3 4 5 stop 90 0 1 6
You will also need a default configuration file. Save the following content to /etc/default/xboxdrv:
To specifiy the amount of controller, edit the variable CONTROLLER_NUM. If you have a wired controller, replace all '-w' occurences with '-i'.
It is generally advisable to use the daemon mode, 'cause it uses less CPU and RAM instead of several xboxdrv processes for each controller.
Additional Configuration Information
Xbox 360 controller glitchy?
According to this post it might help to add the line
dwc_otg.speed=1
to the file /boot/cmdline.txt
.Outdated optional manual configs
Xbox 360 Controller button configuration for retroarch and final burn alpha
/home/pi/RetroPie/configs/all/retroarch.cfg
input exit emulator to exit the emulator and return to emulationstation. input menu toggle to show the retroarch menu (e.g. to set the aspect ratio, save/load the game, etc.)
/home/pi/RetroPie/emulators/pifba/fba2x.cfg
(or /opt/retropie/emulators/pifba/fba2x.cfg
in some versions)Up until now, I didn't figure out how to change the configuration from the analog sticks to the digipad. To exit the emulator, press START and SELECT together.
Alternate Controller Configurations
This is what makes the Xbox 360 controller the best for this project.
- Copy necessary files: First, copy the files above to your pi. (Remove the .txt extension first of course.) I placed them in /usr/local/ but they could go anywhere.
- Edit rc.local: Next, you need to edit rc.local so that xboxdrv uses the config files. There a few different possibilities depending on how you are instantiating xboxdrv, so be careful.2a. If you have this line:change it to this: https://newmood217.weebly.com/how-to-download-ipad-apps-on-iphone.html.2b. If you have this line (generated by the xboxdrv install from retropie_setup.sh):change it to this:2c. Or, if you are using separate lines like this:Edit them so that they look like this:
- File Permissions: The very last step is to make the .cfg files executable. So run these commands, changing them to reflect the location you placed the .cfg files.
Now, whenever you press the Xbox (guide) button on either controller 1 or 2, it will change the control scheme. For player 1, the controller starts up in normal mode. Hitting the Xbox button will change to player1.cfg. Hitting it again will enable mouse emulation. One more time will bring back normal operation. Controller 2 cycles between normal operation and player2.cfg. Controllers 3 and 4 are unaffected.
Here's a little explanation of xboxdrv_player1.cfg (player2 is similar):
2,137 downloads·Added on: October 31, 2016·Manufacturer: Microsoft
The package provides the installation files for Microsoft Xbox 360 Controller USB Driver version 2.1.0.1011.If the driver is already installed on your system, updating (overwrite-installing) may fix various issues, add new functions, or just upgrade to the available version. Take into consideration that is not recommended to install the driver on Operating Systems other than stated ones.
In order to manually update your driver, follow the steps below (the next steps):
1. Extract the .cab file to a folder of your choice
2. Go to Device Manager (right click on My Computer, choose Manage and then find Device Manager in the left panel), or right click on Start Menu for Windows 10 and select Device Manager
3. Right click on the hardware device you wish to update and choose Update Driver Software
4. Choose to select the location of the new driver manually and browse to the folder where you extracted the driver
5. If you already have the driver installed and want to update to a newer version got to 'Let me pick from a list of device drivers on my computer'
Zettaguard Driver Windows 10
6. Click 'Have Disk'7. Browse to the folder where you extracted the driver and click Ok
About Joystick / Gamepad / Wheels Driver:
Installing the controller’s drivers and utilities allows the system to properly recognize the connected device (either wired or wireless products), as well as to use all of the unit’s features, such as force feedback, custom vibrations, and others.
In addition to that, applying the appropriate files lets users configure the controller’s functions and buttons, and might even add support for various accessories compatible with the device.
As for applying this release, the steps are very easy: make sure your operating system is supported by this software, get the package (extract it if necessary), run the available setup, and follow the on-screen instructions for a complete installation.
Even though other OSes might be compatible as well, we do not recommend applying this release on platforms other than the ones specified. In addition to that, after installing the software, we suggest performing a system restart to make sure that the changes take effect properly.
That being said, click the download button, get and install the controller’s software, and enjoy all its available features. Moreover, don’t forget to check with our website as often as possible in order to stay up to date with the latest releases.
In addition to that, applying the appropriate files lets users configure the controller’s functions and buttons, and might even add support for various accessories compatible with the device.
As for applying this release, the steps are very easy: make sure your operating system is supported by this software, get the package (extract it if necessary), run the available setup, and follow the on-screen instructions for a complete installation.
Even though other OSes might be compatible as well, we do not recommend applying this release on platforms other than the ones specified. In addition to that, after installing the software, we suggest performing a system restart to make sure that the changes take effect properly.
That being said, click the download button, get and install the controller’s software, and enjoy all its available features. Moreover, don’t forget to check with our website as often as possible in order to stay up to date with the latest releases.
Xbox 360 Controller Driver Download
- COMPATIBLE WITH:
- Windows XP
Windows Vista
Windows XP 64 bit
Windows Vista 64 bit
Windows 7
Windows 7 64 bit
Windows 8
Windows 8 64 bit
Windows 8.1
Windows 8.1 64 bit - file size:
- 4.8 MB
- filename:
- 2060_8edb3031ef495d4e4247e51dcb11bef24d2c4da7.cab
- CATEGORY:
- Gaming Consoles
Zettaguard Driver Download
It is highly recommended to always use the most recent driver version available.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver.
Problems can arise when your hardware device is too old or not supported any longer.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver.
Problems can arise when your hardware device is too old or not supported any longer.